- High-performance solution based on Realtek chipset
- Support for 2G/3G/4G-modem and channel redundancy
- Wi-Fi 2.4 GHz 802.11b/g/n with support for MIMO 2x2
- Support for GPS and GLONASS
- Power supply via Passive PoE 24 V and DC 9-36 V
WB-15-W is an all-weather Wi-Fi access point with support for LTE and channel redundancy dedicated to connect network equipment to the Internet or departmental/corporate networks.
The device allows to create GRE tunnels through cellular network1, supports router mode, monitoring for quality of connection with a base station and traffic shaping.
WB-15-W is enclosed in case with IP-54 protection level, that allows you to use the device in adverse climatic conditions.
Connection capabilities
There is an opportunity to set up to 2 nano-SIM cards with support for 2G/3G/4G2 to the tray located on the front panel of the device. Ethernet 10/100Base-T connector and Wi-Fi 2.4 GHz 802.11b/g/n provide client with access to a local network.
Only operation via external 2G/3G/4G and GPS antennas is provided.
Performance
High-performance Realtek processors are used to ensure stable and uninterrupted operation. Moreover, the Realtek processors provide high rate of data processing.
HotSpot creating1
WB-15-W provides operation in «Access point» mode that allows to organize mobile HotSpot in public places with portal user authentication (Captive Portal).
The device is capable to provide connection to SoftWLC service platform in OTT mode through third-party carriers networks. It ensures fast and flexible installing without additional actions.
Power supply
Power to the device might be supplied through clamps (in a car) or through Passive PoE technology.
1 The functions will be realized in 1.3.0 firmware version. The current firmware version is 1.1.0.
Interfaces
- 1 port of 10/100Base-T (Ethernet)
- 1 interface of 2G/3G/4G with channel redundancy support
- 2 SMA-type (female) connectors for 2G/3G/4G antennas (Omni, sectoral, panel, etc.)
- 1 SMA-type (female) connectors for external GPS antenna
- Wi-Fi 2.4 GHz IEEE 802.11b/g/n
2G/3G/4G features
- Support for channel redundancy (2 nano-SIM cards)
- Network mode selection
WLAN features
- Support for IEEE 802.11b/g/n
- Data aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx)
- WMM-based priority and planning
- Support for hidden SSID
- 4 virtual access points
- External access points detection
Network functions
- Automatic speed negotiation, duplex mode negotiation and MDI/MDI-X switch-over
- Operation in router mode
- Support for NAT
- Firewall
- Static routing
- DHCP server
- Support for GRE over IPsec1
- Support for ACL
- Support for NTP
QoS functions
- Packet priorities and planning based on profiles
- Bandwidth restriction for each SSID
- Modification of WMM parameters
2G/3G/4G interface parameters
Frequency ranges2
- 4G LTE FDD: B1, B3, B5, B7, B8, B20
- 4G LTE TDD: B40
- 3G UMTS: B1, B8
- 2G GSM: 850M, 900M, 1800M, 1900M
Data rates3
- 4G LTE FDD (Cat 4): 150 Mbps (DL) / 50 Mbps (UL)
- 4G LTE TDD (Cat 4): 130 Mbps (DL) / 35 Mbps (UL)
- 3G DC-HSPA+: 42 Mbps (DL) / 5,76 Mbps (UL)
- 2G EDGE: 384 kbps (DL) / 384 kbps (UL)
Maximum power of the transmitter2
- 4G LTE: up to 23 dBm
- 3G UMTS: up to 23 dBm
- 2G GSM: up to 33 dBm
Wi-Fi interface parameters
- Frequency range: 2400-2480 MHz
- CCK, BPSK, QPSK, 16QAM, 64QAM modulations
- Internal omni-directional antenna
- Support for MIMO 2x2
- Embedded Realtek RTL8197FS chip (IEEE 802.11b/g/n)
- Bandwidth: 20, 40 MHz
Operational channels2
- 802.11b/g/n: 1-13 (2412–2472 MHz)
Data rate3
Receiver sensitivity
Maximum power of the transmitter2
Security
- Centralized authorization via RADIUS server (WPA/WPA2 Enterprise)1 WPA/WPA2 encryption
- Support for Captive Portal1
Configuring
- Management via Telnet, SSH
- Web interface
- CLI
- NETCONF1
Physical specifications
- Maximum power consumption 8 W
- Realtek RTL8197FS processor
- 32 MB Flash
- 128 MB RAM
- Power supply:
- Passive PoE 24 V
- DC 9-36 V
- Operating temperature: from -45°С to +60°С
- IP54 protection level
- Dimensions (WxHxD): 88x232.5x47 mm
- Pole mounted
1 The functions will be realized in 1.3.0 firmware version. The current firmware version is 1.1.0.
2 The number of channels and the value of the maximum output power will vary according to the rules of radio frequency regulation in your country.
3 The maximum wireless data rate is defined according to IEEE 802.11n/ac standard. The real bandwidth can be different. Conditions of the network, environment, the amount of traffic, building materials and constructions and network service data can decrease the real band- width. The environment can influence on the network coverage range.