WEP-2ac Smart

Overview
Specifications
Reviews
  • Smart antennas technology support
  • High-performance solution based on Broadcom chipset
  • Dual band access point with 802.11ac support
  • Power supply: PoE+ (IEEE 802.3at)
  • Operation in cluster without a dedicated server (up to 64 devices)
  • Seamless roaming
  • Up-to-date authentication and encryption means
Solution for enterprise
WEP-2ac Smart provides high-performance, secure, accessible and easy to use wireless network that combines numerous features and services required by corporate clients.
WEP-2ac Smart is a universal solution that may be used for organization of wireless networks in highly crowded areas and high traffic environments (offices, state institutions, conference halls, laboratories, hotels, etc.)

Wireless connection
With support of IEEE 802.11n/ac standards WEP-2ac Smart provides 867 Mbps (5GHz) + 300 Mbps (2.4 GHz) data rates..
The Smart antenna technology used at 5 GHz is based on more than 700 optimized antenna patterns that switch dynamically while access point operation. WEP-2ac Smart analyzes customer and noise source location and uses the best antenna pattern for every moment of time.  

Security
WEP-2ac Smart provides personal data protection and corporate environment security due to the support of up-to-date authentication technologies. Particularly, it uses a dynamic key that is unique for each active client.

Performance
The high-performance Broadcom processors are used in the devices in order to provide reliability and high data processing  rates.

Power supply
The PoE+ technology makes it possible to install the equipment virtually anywhere, regardless of the power supply location, reduce total cost by discarding power cables and perform the installation easier and faster.

Interfaces
  • 1 x Ethernet 10/100/1000BASE-T port (RJ-45) 
  • Console (RJ-45)
WLAN capabilities
  • IEEE 802.11a/b/g/n/ac standards support
  • Data aggregation, including A-MPDU (Tx/Rx) and А-MSDU (Rx)
  • WMM based packet priorities and planning
  • Dynamic frequency selection (DFS)
  • Hidden SSID support
  • 32 virtual access points
  • External access points detection
  • WGB support
  • APSD support
  • WDS support
Network features
  • Automatic speed negotiation, duplex mode negotiation and MDI/MDI-X switch-over
  • VLAN support
  • 802.1X authentication support
  • DHCP client
  • LLDP support
  • ACL support
  • SNMP support
  • IPv6 support
Cluster mode operation
  • Cluster creation with the capacity of up to 64 access points
  • Automatic synchronization of access points configurations in cluster
  • Automatic firmware update in cluster 
  • Single Management IP - single address for access points management in cluster 
  • Automatic frequency channel allocation for multiple access points
QoS functions
  • Profile based packet priorities and planning
  • Bandwidth limiting for each SSID
  • Modification of WMM parameters for each radio interface
Security
  • Centralized authorization via RADIUS server (WPA Enterprise)
  • WPA/WPA2 encryption
  • Captive Portal support
  • E-mail notofications of system events
Wireless interface specifications 
  • Frequency range 2400 - 2480 MHz, 5150 - 5850 MHz
  • CCK, BPSK, QPSK, 16QAM, 64QAM, 256QAM modulations
  • Embedded omnidirectional antennas 2.4 GHz, embedded Smart  antennas on 5 GHz 
  • 2х2 MIMO, Smart Antenna 
  • Two embedded Broadcom BCM47452 (IEEE 802.11a/n/ac) and BCM43217 (IEEE 802.11b/g/n)
Active channels
  • 802.11b/g/n: 1-13 (2412-2472 MHz)1
  • 802.11a/n/ac: 36-64 (5180 - 5320 MHz)
                          100-144 (5500 - 5720 MHz)
                          149-165 (5745 - 5825 MHz)1
Data transfer rate2
  • 802.11ac: up to 867 Mbps
Receiver sensitivity
  • 2.4 GHz: up to -98 dBm
  • 5 GHz: up to -94 dBm
 Maximum power of the transmitter
  • 2.4 GHz: up to 18 dBm1
  • 5 GHz: up to 21 dBm1
Physical specifications 
  • Power consumption below 13 W
  • Broadcom BCM47452 processor
  • 128 MB NAND Flash
  • 256 MB RAM DDR3
  • Power supply:
    – PoE+ 48V/54V (IEEE 802.3at-2009)
  • Operating temperature from +5C to +40C
Configuration
  • Software update and configuration via DHCP Autoprovisioning
  • Remote management via Telnet, SSH
  • Web interface
  • SNMP
  • EMS management system
____________________________________________________________________
1  The number of channels and the value of the maximum output power will vary according to the rules of radio frequency regulation in your country.
2 The maximum wireless data rate is defined according to IEEE 802.11n/ac standard.  The real bandwidth can be different. Conditions of the network,  environment, the amount of traffic, building materials and constructions and network service data can decrease the real bandwidth. The environment can influence on the network coverage range.